4278 Lougheed Highway, Burnaby, BC, V5C3Y5
Dealership hours of operation
Mon - Thu 10:00am - 8:00pm
Fri - Sat 10:00am - 6:00pm
Sun 12:00pm - 5:00pm
Dealership hours of operation
Mon - Sat 7:30am - 6:00pm
Sun Closed
Dealership hours of operation
Mon - Sat 8:00am - 5:00pm
Sun Closed
My Garage

Service FAQs | Destination Honda Burnaby

Why should you service your car at our Destination Honda dealership instead of going to a privately owned vendor?

There are a few reasons why bringing your vehicle into a Honda dealership is better than the next privately owned vendor:

Certified Trained Honda Technicians
Genuine Honda Parts
Peace of Mind

What's the importance of a maintenance schedule?

Your car's maintenance or service schedule is a timeline for what parts or fluids should get replaced or updated based on the kilometers driven. Some factors that may change the maintenance schedule include local driving conditions and driver's behaviour. Maintaining your vehicle and sticking to the factory-recommended maintenance schedule can increase resale value, ensure reliability and maximize the longevity of your vehicle.

Service Procedure Benefit
Air Conditioning

Inspect Operation

Check for proper air-out temperature. If abnormal, check heater adjustment, check operating pressure, and recharge or repair as necessary. Ensure proper operation of the air conditioning system for both cooling and defogging operations.

Air Intake

Replace Air Cleaner Element

Check for proper air-out temperature. If abnormal, check heater adjustment, check operating pressure, and recharge or repair as necessary. Ensure proper operation of the air conditioning system for both cooling and defogging operations.

Air Intake

Inspect Air-Temp Control System (Carbureted Models)

Check the condition of the vacuum actuator that controls the air mix door. Inspection of the Air-Temperature control system on carbureted models will ensure that the unit is operating properly. This system maintains proper air temperature going into the engine to prevent carburetor icing.


Inspect Drive Belt

Measure the belt tension, check for wear and adjust if necessary. Inspect belt for damage, wear and proper tension to guard against belt slipping and/or premature failure. Helps maintain battery charge. Prevents belt squeal.


Replace ABS High Pressure Hose

Relieve high pressure. Remove old hose and install new one. Flush and bleed system with Genuine Honda brake fluid. This increases the reliability of the Anti-lock braking system (ABS). The flexible hose is subjected to high pressure and a loss of pressure would cause the ABS to go into backup mode.


Replace Brake Fluid With Genuine Honda Brake Fluid (Including Anti-lock Braking System)

Remove fluid from brake master cylinder. Add new Genuine Honda brake fluid, flush the system and bleed each wheel cylinder. Remove fluid, refill, and bleed ABS system. Replacing the brake fluid helps to maintain proper hydraulic function of the braking system. This removes water from the system to prevent rusting.


Inspect Discs, Pads, And Calipers

Remove wheels and inspect discs for wear. Measure pad thickness. Check for free caliper movement. This should ensure satisfactory operation of brakes. Should determine friction material condition so the customer can be advised to prevent brake pads from wearing down to the backing plate.


Inspect Hoses And Lines

Brake hoses inspected for damage, leaks, interference, and twisting. Brake lines checked for damage, rusting, leakage, and bends. Brake joints and connections checked for leaks. Inspect brake hoses and lines for leaks or damage.


Inspect Rear Drums, Cylinders, And Linings

Remove rear drums and inspect and measure shoe thickness. Clean brake dust and lube shoe to backing plate contact surfaces. Inspect drums for wear. Inspect the rear brake system. This should ensure that the brakes are operating properly and determine the thickness of the friction material. The wheel cylinders are also checked for leaking brake fluid.


Lubricate Pedal Spring, Bushing And Clevis Pin (Passport Only)

Visually check clutch pedal spring, bushings, and clevis pin for wear or lack of lubrication. Lubricate pedal and release arm pivots. This will maintain smooth operation of these clutch components and minimize their wear.

Cooling System

Replace Engine Coolant

Drain and flush old coolant from system. Add new Genuine Honda anti-freeze/water mixture in a 50/50 ratio. This maximizes radiator, engine, and water pump life.

Cooling System

Inspect Hose\Connections

Hoses and connections inspected for looseness, cracks, and deterioration. Inspect the hoses and connections for leaks or loss of coolant.

Cooling System

Inspect Radiator Core And A/C Condenser

Visually inspect radiator core and air conditioning condenser for signs of damage or corrosion. Inspect the radiator core and A/C condenser for visual leaks of coolant or refrigerant. Early detection can minimize damage to other associated components and minimize the cost of repair, if necessary.

Cruise Control

Inspect Linkage And Hoses (Passport Only)

Check for smooth operation. Check hoses for signs of cracking and splitting. Inspect the cruise control linkage and hoses to ensure that they are operating the cruise control actuator properly.


Inspect Cap, Rotor, Ignition wires, And Timing

Distributor cap removed and inspected. Wires and rotor checked for carbon build-up, cracks, or deterioration. Check ignition timing. Inspect the distributor cap, rotor and ignition wires to ensure that these components will deliver consistent voltage to the spark plugs. Detection and repair of a problem with one of these components should help maintain optimum engine performance.


Replace Oil And Filter

Remove engine drain plug and drain oil. Replace oil filter. Reinstall drain plug with new washer and tighten to proper torque. This will maximize engine life, replenish anti-wear additives and detergent levels to minimize wear or sludge build-up. Changing oil will minimize the build-up of contaminants formed as the results of the normal combustion process that can break down motor oil.

Exhaust System

Inspect Catalytic Converter Heat Shield

Inspect exhaust pipes and muffler. Inspect converter heat shield for condition and tightness. Inspect the catalytic converter heat shield to ensure it is tight and in good condition. This will protect the vehicle and the environment from the heat that the converter produces.

Fluid Levels


Inspect for proper amount and condition of engine oil; differential, transfer case and shift on the fly fluid (if appropriate); transmission fluid; brake fluid; clutch fluid; power steering fluid (if appropriate); coolant; and window washing solution. Check all fluid amount and condition will maximize the car's reliability and minimize inconvenience.


Replace Fuel Filter

Remove old fuel filters and install new filter. This should maintian clean and proper flow of fuel to engine. This should prevent poor performance and potential engine damage due to insufficient fuel.


Inspect Fuel Pipes, Hoses, And Connections

Inspect fuel lines for loose connections, deterioration, and cracks. Inspect fuel lines and connections for leaks or damage to ensure the integrity of the fuel system.


Inspect Idle Speed

Adjust the idle speed, if necessary, when the engine is at operating temperature. Ensure that idle speed is within specifications. This should help maximize fuel economy. Helps prevent premature brake wear on cars with automatic transmission.


Inspect Drive Belt

Apply proper amount of correct lubricant to hinges, seals, door strikers, parking brake linkage, hood latch, seat adjusters, and window channels. This minimizes noise from body movement during turns and when driving over bumps. This allows smoother operation of doors, trunk, and windows. This should prevent premature wear of body and chassis mounts.

Oxygen Sensor


Remove and replace oxygen sensor. An inoperative oxygen sensor will prevent the Engine Control Module (ECM) from adjusting the air fuel to the optimum level potentially causing the vehicle to emit excessive emissions.

Parking Brake

Inspect And Lubricate

Lift vehicle and turn rear wheels to make sure the brakes are not dragging. Adjust parking brake to the proper amount of free play and lubricate the linkage. Ensure that the parking brake is adjusted to proper clearance. Too much clearance will prevent full parking brake application. Too little clearance could accelerate brake wear.

PVC Valve


Ensure that the parking brake is adjusted to proper clearance. Too much clearance will prevent full parking brake application. Too little clearance could accelerate brake wear. Inspect the PVC valve for clogging to minimize the possibility of oil leaks or adverse idle characteristics.

Spark Plugs


Remove old spark plugs and replace with new ones of the proper heat range and gap. Help maintain engine performance. Help maintain low emissions.

Starter Safety Switch


Try to start the vehicle while the clutch is engaged with the vehicle in neutral. Ensure that the starter safety switch is operating properly to prevent starter motor operation when the clutch is not depressed.


Inspect Power Steering System

Test drive to confirm proper operation. Check the power steering fluid level and the steering rack for any leakage. Inspect the power steering system components and hoses for leaks and ensure that the system is operating properly.

Supplemental Restraint System (SRS)


Inspect the SRS components for signs of wear and SRS control unit for diagnostic trouble codes. Inspect the SRS components for visible signs of wear or damage to ensure the high degree of reliability designed into the system is maintained.


Inspect Components/
Mounting Bolts

Check critical suspension bolts with torque wrench to ensure they are properly tightened. Inspect critical suspension bolts for proper torque to prevent chassis noise.

Timing and Balancer

Belt / Water Pump

Replace the timing belt, balancer belt and water pump according to maintenance schedule. Replace the alternator, air conditioning and power steering belts. A broken timing belt or water pump can cause the engine to stop and potentially cause severe damage to the engine valves, cylinder head, and pistons.


Inspect Drive Shaft Boots (CV Boots)

Inspect Drive Shaft Boots (CV Boots) Inspect CV boots for leaks. Early detected leaks from CV boots can be repaired to minimize the potential of CV joint contamination and failure.


Replace Transmission Fluid

Drain old transmission fluid. Refill with Genuine Honda transmission fluid. Replacing the transmission fluid at the proper interval maximizes transmission life.

Transfer Case

Replace Transfer Case Fluid (Passport Only)

Drain old fluid and fill transfer case with the specific amount and proper type fluid. Replacing the transfer case fluid at the proper interval maximizes transfer case life.

Valve Clearance


Remove the valve cover with the engine cold. Measure valve clearance and adjust if necessary. Inspect and adjust the valve clearance to decrease the chance of valve noise.


Rotate Tires

Remove wheel/tire assembly and reinstall based on tire rotation recommendation in the owner's manual. Rotating the tires helps maximize tire life and minimize uneven tire wear.


Inspect Wheel Alignment (Front And Rear)

Install vehicle on alignment rack. Check alignment for proper toe, caster, and camber. Wheel alignment will ensure that the wheels are properly aligned and should minimize uneven or accelerated tire wear.

Service: 1 (877) 698-0914